Whether it be allowing a truck camper battery to charge from it’s engine’s charging system while going down the road or isolating that special battery for sensitive electronics we can handle it. If you are not sure, order the Fuse/Relay box before you order this mounting kit. True Dual Battery Isolators will make simple work of battery isolation in most any RV application. Please note that before you order this mounting bracket kit, you should already be familiar with the tools and skills required to assemble the Fuse/Relay box. This kit includes mounting brackets and hardware for the items listed above (but does not include):Īll wires, ring terminals, grommets, heat shrink tubing specific to the relay/ruse box you decide to use. There are no sharp edges for potential shorts, no wasted space on a negative bus, access to the OEM Relay Block#2, and a professional looking finished installation. In summary, with this option, you get a mount for a waterproof fuse/relay block, a relocation mount for the factory Relay Block #2, and a breaker mount.

Stainless steel mounting hardware included. $57 Victron Energy Smart BatteryProtect 12/24-Volt 65 amp (Bluetooth) (!$60 sold separately)ī: The upper part adds additional space under the relay/fuse block to conceal wires that may need a little slack under the relay/fuse block. This bracket clips into the existing factory main relay/fuse box. TrueAM UTV Dual Battery Wiring Kit With Or Without Battery Meter. This mount relocates the factory Relay Block #2 to this locationĢ: Mounting bracket for a 100A breaker (to be wired between the battery and the auxiliary relay/fuse block). This location ensures accessibility of the factory relay block #2 and does not excessively bend or stretch the cables to the relay block. This bracket repositions the existing relay block between the power steering assembly and body, to make room for the new relay/fuse block that goes next to the factory main relay/fuse box. This mounting bracket set has four pieces:ġ: Factory Relay Block #2 relocation mount. It provides for a low voltage shut-off and does not waste space with mounts for grounding wires because:ġ: there are plenty of factory grounding points located throughout your truck.Ģ: there is a ground point right next to the battery about 1 foot from the location of the fuse block. My design is waterproof and does not obstruct access to the Toyota Relay Block #2. The most popular alternative is a Blue Sea fuse block mounted on a metal bracket.

I also wanted my relay/fuse block to look like it was installed by Toyota. I designed these mounting brackets for an auxiliary relay/fuse block on my 2022 Tacoma because I wanted a solution that was waterproof, safer, and more reliable than the most popular alternative available. True introduces a 2021 UTV dual battery kit for Honda 1000-5, 1000, 700, 500 series based on consumer demand on power and performance. The SBI’s internal LED will glow blue.Ģ. When all voltage sources drops below 12.9 volts* (cut out threshold) the SBI will disengage and the blue LED will go out.ģ. When the SBI LED is out the batteries are separated thus preventing the power of your start battery from being drained by use of the accessories powered from the second battery.Ĥ. When the vehicle is restarted and the start battery has recharged to 13.4 volts* the SBI engages, the LED will illuminate and the second battery is connected to receive charging.If you want to add a waterproof relay/fuse block (sold separately) to your 2016-2022 Toyota Tacoma, you can achieve a factory (OEM) look with these custom 3D printed mounting brackets. The consumers have spoken and we listened.ġ. When the engine is running and the charging source raises the voltage of the start battery to 13.4 volts* (cut in threshold), the True Smart Battery Isolator (SBI) engages and connects the two batteries to charge simultaneously. Specifically designed to leave suspended or mount to any flat clean surface (even the battery case) with the included 3M Dual Lock™ or any other surface with the included screws. More durable with stud placement that allows for simple easy connection.It is designed with TrueAm’s PEP® programming which insures you maximum efficiency and battery attribute protection. The TRUE-AM UTV-SBI-18 has been designed for efficiency focusing on every aspect of installation and operation on today’s stator based electrical systems.

This is the first and only Smart Battery Isolator designed from the ground up exclusively to meet the demanding needs of the UTV marketplace. Developed from years of interaction with, and feedback from, UTV owners worldwide we are proud to introduce the completely new TRUE UTV-SBI-18 TrueAm has just introduced a new battery isolation product for the UTV marketplace. The Lithium Battery Isolator UTV-SBI-19L includes: The ONLY 100 UTV designed Battery Isolator available w/PEP Lithium.

True utv battery isolator